Bulk SMS

WHAT IS WiFi?

The term "Wi-Fi" suggests "Wireless Fidelity", comparing with the long-established audio recording term "High Fidelity" or "Hi-Fi", and "Wireless Fidelity" has often been used in an informal way, even by the Wi-Fi Alliance itself, but officially the term does not mean anything. Wi-Fi is simply a trademarked term meaning IEEE 802.11x.

The name of a popular wireless networking technology that uses radio waves to provide wireless high-speed Internet and network connections. The Wi-Fi Alliance, the organization that owns the Wi-Fi (registered trademark) term specifically defines Wi-Fi as any "wireless local area network (WLAN) products that are based on the Institute of Electrical and Electronics Engineers' (IEEE) 802.11 standards."

Initially, Wi-Fi was used in place of only the 2.4GHz 802.11b standard, however the Wi-Fi Alliance has expanded the generic use of the Wi-Fi term to include any type of network or WLAN product based on any of the 802.11 standards, including 802.11b, 802.11a, dual-band, and so on, in an attempt to stop confusion about wireless LAN interoperability.

Wi-Fi works with no physical wired connection between sender and receiver by using radio frequency (RF) technology, a frequency within the electromagnetic spectrum associated with radio wave propagation. When an RF current is supplied to an antenna, an electromagnetic field is created that then is able to propagate through space. The cornerstone of any wireless network is an access point (AP). The primary job of an access point is to broadcast a wireless signal that computers can detect and "tune" into. In order to connect to an access point and join a wireless network, computers and devices must be equipped with wireless network adapters.

Wi-Fi is supported by many applications and devices including video game consoles, home networks, PDAs, mobile phones, major operating systems, and other types of consumer electronics. Any products that are tested and approved as "Wi-Fi Certified" (a registered trademark) by the Wi-Fi Alliance are certified as interoperable with each other, even if they are from different manufacturers. For example, a user with a Wi-Fi Certified product can use any brand of access point with any other brand of client hardware that also is also "Wi-Fi Certified". Products that pass this certification are required to carry an identifying seal on their packaging that states "Wi-Fi Certified" and indicates the radio frequency band used (2.5GHz for 802.11b, 802.11g, or 802.11n, and 5GHz for 802.11a).

How to secure your WiFi network?

When you buy a wireless router you might find an Installation CD by vendor that CD with guide you through a wizard on setting up router. Here are some suggestions that how can you setup security on the router without using the application software.

  • Open a new browser.
  • You may now type IP address of the router in your browser. The step here is where you can get the management system of the router. Due to different vendors, you need to lookup on your router’s manual for the IP address usually it may be 10.10.10.01, 196.168.1.1 or 192.168.0.1, 100.100.100.1 or something similar to those matches and the default password of the router. Every router management console is different from each other. Try exploring around and find the appropriate section to manage
  • You should never forget this step to setup an administrative password. The step to set here is often not located in Security section; you will need to take a look at the utilities, user management or system settings. Find it and change the password immediately for any user account.
  • Enable Wireless security. To turn on your encryption look under the wireless security tab. The step over here will need you to either use WPA or WPA-PSK and this will only appropriate if the devices on your network supported it. Otherwise you will need 128-bit WEP. For WPA or WPA-PSK, you would have to type pass phrase/password into a piece of paper and transfer to thumb drive so that you can set the password in the client’s machines.
  • Change your SSID. You should not make your SSID this will be probably a default SSID, normally those who do not configure their SSID will have their router name such as “linksys”, “belkin”, “dlink” etc. Try changing it with someone menacing, which will be threat for them to connect. Like virus geek, virus spreader. Remember that you will need this SSID when you browse through the network from your client machines. You can find these settings in the section of Channel or SSID.
  • Save your configurations and settings by pressing the save changes or save settings button. You will need to save every change that you will make to the router in order to it can take effect and probably you will have to reboot your router multiple times.


Contact Us | Sitemap | Payment Options | Terms & Conditions | Privacy & Anti-Spam Policy | Disclaimer | FAQ
Copyright 2005 SMS.IN - All rights reserved.